4
Tools and Parts
Gather the required tools and parts before starting installation.
Read and follow the instructions provided with any tools listed
here.
Tools needed (all models)
■ Level
■ Drill
■ ¹⁄
8”(3.0mm)drillbit
■ Pencil
■ Pliers
■ Tape measure or ruler
■ Caulking gun and weatherproof caulking compound
■ Flat-bladescrewdriver
■ Phillips screwdriver
■ Saber or keyhole saw
■ Metal snips
■ Vent clamps
Parts Supplied
Remove parts from packages. Check that all parts are included.
■ 1-30”x12”(76.2x30.5cm)facepanel
■ Damper
■ 2-40Wincandescentlamps(onlymodelEAS428SS)
■ 2-50Whalogenlamps(onlymodelEPR628SS)
■ 2-Metalgreaselters
■ 2-Mountingbrackets
■ 2-Metalspacers(forusewhencabinetdepthisgreater
than12”)
■ Hardware package. Includes:
• Installation Instructions and Use and Care Guide
• 8-metalwashers
• 8-plasticwashers
• 10-4.5x13mmwoodscrews
• 2-4.2x15mmmachinescrews
• 4-3.5x9.5mmat-headsheetmetalscrews
• 8-4.2x19mmsheetmetalscrews
• 6-3.5x9.5mmsheetmetalscrews
• T10 TORX®† adapter
Parts needed
■ 6”(15.2cm)roundmetalventsystem
†®TORX is a registered trademark of Saturn Fasteners, Inc.
Location Requirements
IMPORTANT: Observe all governing codes and ordinances.
Haveaqualiedtechnicianinstalltherangehood.Itisthe
installer’s responsibility to comply with installation clearances
speciedonthemodel/serialratingplate.Themodel/serialrating
plateislocatedinsidethelinerbehindthelterontheleftwallof
the range hood.
Range hood location should be away from strong draft areas,
such as windows, doors, and strong heating vents.Cabinet open-
ing dimensions that are shown must be used. Given dimensions
provide minimum clearance. Consult your cooktop/ range manu-
facturer installation instructions before making any cutouts.
Grounded electrical outlet is required. See “Electrical Require-
ments” section.
The range hood is factory set for vented installations through the
rooforwall.Fornon-vented(recirculating)installationssee“Non-
Vented(recirculating)InstallationThroughtheSoft/Cabinet”in
the “Prepare Location” section. Recirculation Kit Part is available
from your dealer or an authorized parts distributor. All openings
in ceiling and wall where range hood will be installed must be
sealed.
For Mobile Home Installations
The installation of this range hood must conform to the
Manufactured Home Construction Safety Standards, Title 24
CFR,Part328(formerlytheFederalStandardforMobileHome
ConstructionandSafety,title24,HUD,Part280)orwhensuch
standard is not applicable, the standard for Manufactured Home
Installation1982(ManufacturedHomeSites,Communitiesand
Setups)ANSIA225.1/NFPA501A,orlatestedition,orwithlocal
codes.
Product Dimensions
I*
I*-Metallicspacers
Spacers has to be installed
and used when cabinet depth
is greater than 12”.
I*
AAR428SS / AGR628SS range hood models
Dimension
DIM A 28
1
⁄4”(71.8cm)
DIM B 26”(66cm)
DIM C 1⅛”(2.9cm)
DIM D 10¾”(27.3cm)
DIM E 9½”(24.2cm)
DIM F
5
⁄16”(.85cm)
DIM G 14
9
⁄16”(37cm)
DIM H 6”(14.8cm)
DIM I ½”(1.27cm)
Comments to this Manuals