Arietta ALS436SS Instruction Manual download pdf (Page 3)

†®TORX is a registered trademark of Saturn Fasteners, Inc.

Gather the required tools and parts before starting installation.

Read and follow the instructions provided with any tools listed

here.

CAUTION:

Remove carton carefully, Wear gloves to protect against sharp

edges.

Tools needed (all models)

■ Wire nuts

■ Metal duct lenght to suit installation

■

⁄2 ” Romex wire connector

■ 6” rounded metal duct lenght to suit installation

■ Measuring tape

■ Pliers

■ Gloves

■ Knife

■ Safety glasses

■ Electric drill with

⁄16” and

⁄8” Bits

■ Spirit level

■ Duct tape

■ Screwdrivers:

■ Philips (Posidrive #2)

■ Torx #2

■ Wire cutter/ stripper

■ Masking tape

■ Hammer

■ Saw, jigsaw or reciprocating saw

Parts Supplied

Remove parts from packages. Check that all parts are included.

■ Hood canopy assembly with blower.

■ Lamps already installed.

■ Air transition

■ Grease lter

■ Duct covers

■ Hardware package. Includes:

• Template

• Duct cover support bracket (1 piece)

• Use, care and installation guide

• Wood screws (6 pieces- 5 x 45 mm)

• Concrete wall anchors (6 pieces- 8 x 40 mm)

• Assembly screws (4 pieces - 4.2 x 8 mm)

• Air transition screws (2 pieces - 3.5 x 9.5 mm)

• TORX 10 adapter

• TORX 20 adapter

Optional Accesories

■ Recirculation KIT (KIT01937).

Tools and Parts

Location Requirements

IMPORTANT: Observe all governing codes and ordinances.

Have a qualied technician install the range hood. It is the

installer’s responsibility to comply with installation clearances

specied on the model/serial rating plate. The model/serial rating

plate is located behind the left lter on the rear wall of the vent

hood.

Canopy hood location should be away from strong draft areas,

such as windows, doors and strong heating vents.

Cabinet opening dimensions that are shown must be used. Given

dimensions provide minimum clearance.

Grounded electrical outlet is required. See “Electrical Require-

ments” section.

The canopy hood is factory set for venting through the roof or

wall. For non-vented (recirculating) installation, the KIT01937

must be purchased with your provider.

For Mobile Home Installations

The installation of this range hood must conform to the

Manufactured Home Construction Safety Standards, Title 24

CFR, Part 328 (formerly the Federal Standard for Mobile Home

Construction and Safety, Title 24, HUD, Part 280) or when such

standard is not applicable, the standard for Manufactured Home

Installation 1982 (Manufactured Home Sites, Communities and

Setups) ANSI A225.1/NFPA 501A, or latest edition, or with local

codes.

Product Dimensions

6”

(15.24 cm)

⁄4”

(27.3 cm)

⁄16”

(33.5 cm)

Ductless (recirculating)

version only

*Max 42

⁄16” (108 cm)

*Min 28

⁄16” (71.7 cm)

Ducted version only

*Max 38

⁄16” (98.76 cm)

*Min 24

⁄16” (62.4 cm)

5”

(12.6 cm)

⁄16”

(50 cm)

30” (76.2 cm)

36” (91.4 cm)

1 2 3 4 5 6 7 8 ... 23 24

Comments to this Manuals

No comments

Arietta ALS436SS Instruction Manual Page 3

Comments to this Manuals

Related products and manuals for Cooker hoods Arietta ALS436SS